201726 — My only experience with a bad bearing was one that started to make a little noise. We drove about 50 miles on it, and then it started to grab ...

My biggest concern is to actually have this interpretation to be supported by a standard, so that it could be implemented as the default interpretation for all costumer drawings we receive.

Failed wheel bearings do indeed make noise, can sound like snow tires at high speed…As Knuckles said, you can jack up the wheels one at a time and FEEL & LOOK for play in the wheels…

Office of Coast Survey National Oceanic and Atmospheric Administration U.S. Department of Commerce. Home; Future of NOAA Charts.

Chamfer calloutSolidWorks

Roaring is usually a sign of a bad wheel bearing and as it get worse will usually turn into a popping or grinding noise, at this point they’re usually on their last few miles.

I have a question…I have a '03 Toyota Camry with 4 cyl and auto trans. This has 118k miles. I’m wanting to know what symptoms bad wheel bearings will give. Why? I am Deaf and obviously can’t hear. I know there’s a way to test for bad wheel bearings by wheel but I’m wanting to know if can do it by feeling? Whenever I’m driving between 40-50 mph, I get a very fine humming feel on my steering wheel. I can sense if there is a wheel out of balance but this doesn’t feel like it…my steering wheel feels like a vibrating sander, you know? Just wondering if that means bad wheel bearings or something else? Thanks!

Engineers apply the knowledge of math & science to design and manufacture maintainable systems used to solve specific problems. AskEngineers is a forum for questions about the technologies, standards, and processes used to design & build these systems, as well as for questions about the engineering profession and its many disciplines.

My question is the following. If I were to inspect a part considering the drawing on the first image (45° chamfer angle indicated with a note), am I supposed to measure one linear dimension of .06 and measure the 45° with the applicable general tolerance? In that case, which of the two linear dimensions should I measure? I wasn’t able to find a clear explanation for this in the ASME Y14.5 standard.

Sony E-mount adapted ROKINON 75-200 mm F/4 manual focus Telephoto Macro Zoom Lens. Filter size - 55 mm. Weight - 577 g with Adapter. This lens has a size of ...

Chamfersymbol in engineering drawing

I’d go ahead and replace the half shaft that has the torn boot. It’s likely the CV joint is damaged from lack of grease and dirt and water getting to it.

If the right CV joint is bad, I will go ahead and replace the left one too since it probably isn’t far behind. I just would like confirmation that a bad CV joint can cause all this? Thanks for your advice!

Holechamfer callout

Ok thanks for the diagnosis. Can it be determined how much it would cost to replace wheel bearings in my area (Knoxville, TN)? Should it be inexpensive? Thanks.

1. It Saves Hours of Labor. Depending on the car, replacing the water pump or timing belt can take between a few hours and a full day.

Many folks misdaignose problems as tire related when they are actually bearing and CV joint related. I think Busted is right - especially about not waiting to get this looked at.

Chamfer callouton drawing

An abnormality in tire tread wear can also mimic a worn wheel bearing and this is easily checked. I assume this has been done. Another possibility could be a failed motor mount which could set up a quirky vibration. (Check the dog bone mount under the hood on the passenger side top. That’s the most common failure and easily fixed if a problem.)

I asked my younger brother who was in town for business to drive my car tonight to see if it was making any noise. Sure enough it was. My brother said it was roaring loudly from the front end driving from 25 MPH to highway speed. More scary now since I can’t hear that and not know if it will break on me… I think this is more definite confirmation the CV axles are about to disintergate on me so I will have them replaced this week and post back on if it was the culprit.

GD&Tchamfer callout

This bearing material is excellent for marine applications but may also be suitable for other extreme conditions where bearings are exposed to other acids – to ...

One is to jack the vehicle up so that tire is off the ground. Grab the tire at the 12:00 and 6:00 oclock positions and try rocking the top and bottom of the tire in and out to check for play in the bearing. If the tire rocks that bearing is worn.

Another way to check for a worn bearing is with the tire off the ground, place your hand on the strut spring. Now slowly rotate the tire. If the bearing worn, the roughness of the bearing will be transfered into the strut spring where it can be felt.

Alternatively, and what I think makes more sense, should I just interpret the chamfer as two identical linear dimensions (because it is 45°) and apply the same tolerances individually for both? And, in that case, consider the 45° as a basic dimension without any tolerance? In other words, can the indicated chamfer in the first image be interpreted as the exact same way as the chamfer in the second image?

The bottom line is that you’ve searched properly for the source of the vibration, you’ve found that you need new half-shafts, so go ahead and fix that first, then see how it feels.

Standardchamfersize Chart

For what it’s worth, I’ve had bad hearing for decades for a variety of reasons and as a mechanic I’ve had to focus more on attuning myself to the feel of a problem rather than the audible end of things. So yes, you can determine many faults by feel instead of with the ears.

Ok now…I jacked up the front of the car and did the “12:00 and 6:00” method. Both wheels are tight and snug. I did the hot wheel temperature and both wheels are cool to the touch. With that, I could have ruled out wheel bearings. Now I decided to take a look under the right front corner. And I found the CV joint boot had thrown grease from the boot all over. I think the CV joint is the culprit. Could a bad CV joint cause all this vibration and humming sound?

Shop our inventory of wheel hubs and bearings for sale at AutoShack! We have wheel bearing parts from complete assemblies to individual mounts.

Having now heard that it’s producing a “roaring” sound, I too think it sounds like a bearing. However, you know you need half-shafts anyway, so I’d do those first and see how it feels.

I can confirm for you that a bad CV joint can manifest itself as a 'buzz saw" vibration in the steering wheel. As can other things.

I’m not sure who it was (Caddyman? Keith? Someone else?) who had a link for replacement shafts that aren’t much more than rebuilds, but seem to be much more reliable. Hopefully they’ll pop on soon and post the link for you.

The best way to test for a bad bearing is to jack up the wheel from the suspected axle side and do a manual feel test. If the properly mounted wheel can be wiggled up and down and side to side, this is a sure sign the wheel bearing has failed. If the wheel bearing is simply worn, but holding, the wheel should be removed, the brake pads removed, and the axle spun by hand. A good wheel bearing with allow the axle to spin smoothly with some small amount of resistance. If you feel any roughness in the spinning motion, the wheel bearing is probably bad.

asme y14.5chamfer callout

Mityvac MV7201 Fluid Evacuator Plus enables quick and clean oil changes. Ideal for extracting or dispensing fluids in vehicles.

TP-038 Piston T-Seal | TP Style | Buna-N Rubber Material | 3 1/2 in Inner Diameter | 3 7/8 in Outer Diameter | 0 to 5000 psi Pressure Range.

Just to let you know, I’ve worked on cars for over 20 years, and most of the problems I encounter are determined more by feel than by sound. While I can hear problems in cars as they are pulled up, determining the cause of the sound almost always comes down to feeling for the problem. If you are unable to determine the cause of the vibration yourself, please let a mechanic look it over for you. The feeling your describing appears to be coming from the wheel/hub/suspension components none the less, and a failed component in this area is very dangerous and can lead to loss of control.

Chamfer calloutexample

Mar 4, 2024 — A bad wheel bearing, however, can really impact your driving - and your safety. And it's a big part of why a faulty wheel bearing should be ...

Conversion 95 mm into inches, convert 95 mm, convert mm into inches, 95 mm how many inches?

Anytime I suspect a bad wheel bearing I jack up the suspected corner of the car and try to wiggle the wheel while watching for play in the hub area. Just the wheel moving could be a sign of a bad ball joint or tie rod end, but if it’s moving in the hub area it’s the wheel bearing. If you have an infrared thermometer check the temperature of the wheels after driving a few miles. If a wheel bearing is bad usually there will be a significant amount of heat transfer to the wheel. If you check the temperature by hand be careful, I’ve seen wheels get extremely hot from a bad wheel bearing. I actually saw the hub and wheel on my father in laws truck smoking from the heat of bad bearing one time and the lug nuts were so hot I couldn’t touch them.

Yes, that would be the problem. In all likelihood, that joint needs repairing/replacing. Common repairs often fail (seems to be the consensus from this thread), and since you’re now feeling a humming, that implies there’s some damage to the joint itself. Your best bet, at this point, is to replace the axle with a new or rebuilt unit. Again, the consensus here is that rebuilt shafts don’t work all that well, nor last that long.

Roaring is usually a sign of a faulty wheel bearing, not a CV joint. If this turns out to be a wheel bearing I would suggest replacing both sides if possible

I am having a bit of trouble concerning the interpretation of the tolerance of a 45° chamfer, and I wanted to see if any of you could help me with this.

The feelings you describe certainly seems like a wheel bearing. However, worn-out brakes can also cause this feeling. Worn-out brakes typically feel worse when braking-however. If the feeling only seems to get worse when turning, I think you are on the correct track in assuming a bad bearing.